Recently watched
EC Milwaukee MW302 electronic meter
Information on product

EC Milwaukee MW302 electronic meter

  • NEW EC meter / water measuring tool
EC Milwaukee MW302 electronic meter
Manufacturer: Milwaukee
111.47 / 1szt.
In stock
Zadaj pytanie
Poleć znajomym
Recommend this product

If You want to tell Your friend about this product, please use the form below.

To:
This field is required for placing an order.
To add more e-mail addresses, remember to separate them by comma
Signature:
This field is required for placing an order.
Content:
This field is required for placing an order.
fields marked with - This field is required for placing an order. - are required
Zapytaj o produkt

If description is not sufficient for You, please send us a question about this product. We will reply as soon as possible.

Your e-mail:
This field is required for placing an order.
Question:
This field is required for placing an order.
fields marked with - This field is required for placing an order. - are required

DESCRIPTION

PORTABLE INSTRUMENT TO MEEL EC MODEL: MW302

Sturdy electronic EC-meter with LCD display

(for measuring the content of nutrients in solution)

In the hydroponic cultivation, TEN TANK will allow you to check if plants have already absorbed nutrients - you should replace the solution.

It also makes it easier to set up your own nutrient solution (without using fertilizer manufacturers'' tables) and to minimize the risk of "burning" plants through the overdose of fertilizers

INSTRUCTIONS FOR OPERATION :

- The meter is compatible with a 9V battery. It is necessary to slide the flap on the back of the device and insert the batteries according to the poles.

- Connect the probe to the instrument by aligning the tip of the plug.

- Make sure that the meter has been properly calibrated before taking any measurement. (see "calibration procedure")

- Dip the tip of the EC probe (approx. 4 cm) into the solution. If possible, use a plastic pot to minimize EMC interference.

- Turn on the instrument (ON) with the ON / OFF button.

- Wait for the temperature sensor to reach the level of thermal equilibrium before taking the measurement.

- After taking the measurement, turn off the instrument (OFF). The probe should be cleaned and well dried. You can use alcohol for better cleaning.

 

CALIBRATION PROCEDURE:

NOTE: always use the calibration table on the calibration solution package

- Clean the probe with alcohol and let it dry out.

- Open the vessel with the calibration solution (see "specification") and immerse the probe making sure that the metal tips are completely immersed.

- Wait for the thermal balance to be reached and the reading will be stable.

- Adjust the calibration knob on the back of the instrument with a screwdriver so that the value appears

1.4 mS / cm = 1400uS / cm (if the table on the calibration fluid does not state otherwise)

- At this stage, the calibration is completed, the instrument is ready for use.

- It is recommended to re-calibrate the device once a month and when the battery or probe is replaced.

 

BATTERY CHANGE:

When the batteries are close to exhaustion, the instrument will show "V".

When the low battery indicator appears, it means that they have about 50 hours of operation. Poor batteries may cause the device to show erroneous readings.

It is recommended to replace the batteries regularly. The batteries can only be replaced in a safe place. It must be a 9V battery. Turn off the device, slide the flap and replace the 9V battery with a new one. We need to be sure that the battery has been inserted in accordance with the poles, and then we close the flap again.

 

SPECIFICATION

SCOPE / RESOLUTION 0 to 10.0 mS / cm / 0.1 mS / cm

ACCURACY (approx. 25 ° C) ± 0.2 full scale

CALIBRATION SOLUTION 1.41 mS / cm (M10031B)

CONDUCTIVE PROBE SE520

ENVIRONMENT 0 to 50 ° C, 95% RH max.

BATTERY TYPE 1 x 9V

BATTERY OPERATION approx. 300 hours

DIMENSIONS 145 x 80 x 40 mm

WEIGHT 220g (with battery)

The built-in microprocessor guarantees fast and accurate measurement

Replacement electrodes available on request

Guarantee for the electrode: 6 months

Usable use value: 1-2 years

Slim and compact - 145 x 80 x 40 mm

For proper use and calibration, calibration fluids are required: 1413μS / cm and CLEANING and STORAGE electrodes

Included:

- fluid for calibration 

- power supply (standard 9V

Users reviews
This page uses cookie files to provide its services in accordance to Cookies Usage Policy. You can determine conditions of storing or access to cookie files in your web browser.
Close
pixel